DTXP4100   DuraTrax   IntelliPeak AC/DC Pulse Charger 

TECH NOTES
      This is an IntelliPeak AC/DC Pulse Charger for Charging/Discharging
      Nickel Cadmium (NiCd) and Nickel Metal Hydride (NiMH) Battery Packs.
      CHARGES HPI2012 6V 1200MAH BATTERY PACKS AT LOWEST RATE OF CHARGE	

      Note: Do Not Discharge Battery Cells smaller than Sub-C Size
                  ("Sub-C" is one size smaller than a "C" size).

FEATURES: Peak charges nickel-cadmium batteries using specialized peak charging
            technology as well as nickel-metal hydride batteries, plus
            discharging and cycling features not commonly found in other
            chargers.
          "Negative Delta V" peak detection for NiCds and NiMHs.
          Built-in Artificial Intelligence to eliminate false peaks.
          Auto-identifies the quantity of cells being charged.
          Computerized control, 8-bit 4MHz CPU with 8K ROM, 1K RAM,
            1-channel 16-bit analog-to-digital converter.
          High efficiency P-Channel MOSFET drive transistors.
          11-15V DC input.
          Built-in AC power supply.
          Output: 4-7 cells on DC, 4-8 cells on AC.
          Adjustable fast charge current of 0.5-4.0 amps AC, 0.5-6.5 amps DC.
            (Note: 3 amp maximum charge rate recommended with NiMH packs.)
          Pulsed fast charge, with 8-bit pulse width modulated current control
            output.
          100mA trickle charge.
          1 amp fixed discharge rate.  Fixed 2.60V discharge cutoff voltage-
            (see COMMENTS).  Not designed for discharging A or AA size (and
            smaller) cells (see COMMENTS).
          Cycle functions: Select a single discharge/charge cycle for periodic
            pack conditioning, or continuous "auto-repeat" cycles for reviving
            batteries that have developed a memory, or for breaking in a new
            pack.
          Four multi-function, high intensity LED indicators. Status light
            glows during charge and flashes when nearing peak.
          Audible mode select tone signals for easy set-up.
          Reverse polarity and fused overload protection.
          Designed to charge sub-C battery packs.
          One Year Warranty

INCLUDES: One IntelliPeak AC/DC Pulse Charger w/5' AC Power Cord
          One Standard Battery Connector with wire lead (Kyosho-type)
          One DC power cord with alligator clips
          One Instruction Sheet
          One DuraTrax Decal Sheet

REQUIRES: DC power source of 11-15 Volt, OR AC power source of 110 Volt (United
            States Standard AC)
          Battery pack with and Standard Connector (Tamiya-type)

SPECS:    Battery Types:         Nickel-Cadmium (NiCd)
                                 Nickel-Metal Hydride (NiMH)
          Charger Type:          Pulsed Current, Peak Detecting
          Peak Detection Method: Negative Delta V
          AC Input Voltage:      110 (United States Standard AC)
          DC Input Voltage:      11-15V DC
          Number of Cells:       4-7 cells DC or 4-8 cells with AC power supply
          NiCd Fast Charge:      0.5-4.0A AC
                                 0.5-6.5A DC
          NiMH Fast Charge:      0.5-3.0A (3 amps is the maximum recommended
                                            charge rate)
          Trickle Charge Rate:   100mA
          Discharge Rate:        1 amps fixed
          Discharges down to a fixed voltage of 2.60 volts.
          Width:                 3.0"
          Height:                3.125"
          Depth:                 5.0"
          Weight- Charger:       3 lb
          Meter Display:         No

COMMENTS:
          Discharging cells smaller than sub-C size:
            Do NOT Discharge Cells which are Smaller than Sub-C Size. This is
            to include A and AA size (and smaller) cells which are normally
            installed inside radio transmitters and so on. The discharge
            current rate of the IntelliPeak is too high for such smaller cells
            and the wiring which is used to assemble such packs. Failing to
            avoid this will likely cause permanent damage to the cells and/or
            wiring in the battery packs, and possibly the equipment in which
            the battery is installed.

          Fixed discharge cutoff voltage-
            The IntelliPeak Charger has a fixed discharge cutoff voltage
            setting of 2.60V. This cutoff voltage is not adjustable. If a
            specific discharge cutoff value other than 2.60V is desired,
            monitor the pack voltage during discharge with a separate voltmeter
            (or the built-in LCD on the IntelliPeak Digital Pulse Charger) and
            manually terminate discharge at such point as desired.

          NiMH Battery Care and Handling: It is important not to allow NiMH
            batteries to overheat while being charged. Heat can adversely
            affect the performance of NiMH batteries. If overheating is
            observed, disconnect the battery from the charger immediately
            and reduce the charge rate for future charging needs.
           -Also, Do Not Deep-Cycle NiMH batteries. Permanent damage could
            result. Store NiMH packs with some voltage remaining in the cells.
           -Use a NiMH battery pack no more than three cycles per day, with a
            two to three hour break in-between for cooling. More frequent use
            will likely overheat the pack.
          WARNING: Do Not leave charger unattended during fast charge. If the
            battery or charger becomes hot at any time, disconnect the battery
            from the charger immediately.
           -Do Not charge 4 or 5 cell batteries at a rate greater than 4.5 amps
            as this could cause excessive heating in the charger itself.

          Other IntelliPeak Chargers Comparison-
          All Intellipeak Chargers-except DTXP4150 Intellipeak Twin-include:
            Ability to charge NiCd and NiMH packs.
            Adjustable pulsed current.
            Cycling functions (single cycle: periodic conditioning of regularly
              used batteries, and auto-repeat cycle: for deep conditioning of
              new or unused batteries.
            Four multi-function LEDs and audible tones to ease setup.
            CPU driven.
          *Each one builds up to the next one:
           -Pulse Charger: AC/DC input, 1 amp discharge rate, great for racers
              and sport modelers alike.
           -Mini Pulse Charger: Builds on the Pulse Charger's features with DC
              input, detachable AC power supply...charger itself is very small,
              great for portability, 2 amp discharge rate, 1 built-in cooling
              fan.  Note: This charger will only go down to a 1 amp charge
              rate (The others chargers go down to .5 amps).
           -Deluxe Pulse Charger: Adds to the Mini Pulse Charger's features
              with DC input, detachable AC power supply. 2 and 10 amp discharge
              rate (faster discharge ability). Negative Delta V (for Nicads)
              and Zero Delta V (for NiMHs) peak technologies, auto-selects.
              High rate charging for high-capacity NiMH packs. Two built-in
              cooling fans.
           -Digital Pulse Charger: Includes all of the Deluxe model's features
              plus LCD readout that shows battery voltage, charge current,
              and discharge capacity in milliamps.

| Homepage | R/C Airplanes | R/C Boats | R/C Cars | Batteries | Chargers | Search |