HPI761    RTR Sprint 2 Drift 350Z 

TECH NOTES

This is the 1/10 scale, electric powered, radio controlled, ready-to-run
HPI On-Road Sprint 2 Drift Car with the Nissan 350Z Body.
_
FEATURES: Chassis: 3/16" (4mm) plastic
Drive: Four wheel belt drive
Motor: 17 turn Nosram Tornado SS3 17x2, aluminum motor mount
Radio: HPI TX-2 pistol grip AM 27MHz with steering and throttle trim
and reverse and SX-1 steering servo, transmitter has charge jack
Ball Bearings: Full set included
Shocks: Oil-filled, plastic bodied, with special springs for drifting
Differentials: Planetary gear
Transmission: Single speed
Tires: Hard compound drift type X-pattern, 1" (26mm) wide, 2.5"
(65mm) outer diameter
Wheels: Officially licensed TE37 Rays/Volk design 5-spoke chrome
plated, outer diameter 1.9" (48mm), width 1" (26mm), 3mm offset in
front and 6mm offset in rear for wide look seen on full-size drift
cars
Speed Control: Electronic, Nosram Hawk with reverse
Pinion Gear: 48 pitch steel
Spur Gear: 48 pitch, 87 tooth, composite construction
Body: Clear polycarbonate untrimmed Nissan 350Z with rear wing
Bumpers: Front, foam
Suspension: Fully adjustable
Ackerman: Adjustable, Ackerman describes the effect of the inner
front wheel turning faster than the outer front wheel during turns
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Steering: Bell-crank type with servo saver

INCLUDES: HPI On-Road Sprint 2 Drift Car with the Nissan 350Z Body, motor,
electronic speed control, clear body, tires, foam inserts, wheels
pinion gear,  87 tooth spur gear, 2-ch radio, servo, two decal
sheets, instructions
_
REQUIRES: Radio Batteries: (8) AA size
Battery: 6-cell 7.2V stick with standard connector
Battery Charger: Timed or peak for 6-cell battery
Paint: Polycarbonate safe spray or brush-on
Misc. Items: Building and track equipment

SPECS:      VEHICLE-
Length:     14.5"  (369mm)
Width:       7.5"  (190mm)
Height:      5"    (127mm)
Weight:      3.1 lbs (1410g) approx.
Wheelbase:  10"    (255mm)
Front Track: 7.38" (187.5mm) side to side at outer edges of wheel
Rear Track:  7.7"  (194mm)
Front Tread: 6.5"  (166mm)
Rear Tread:  6.8"  (173.5mm) side-to-side at wheel centers
Ground Clearance: 0.31" (8mm)
BODY-
Length:     16.5" (419mm)
Width:       7.7" (195mm) at rear wheels (widest point)
7.1" (180mm) behind from wheels (thinnest point)
Height:      5"   (127mm)

COMMENTS: For Replacement Ball Bearings use:
Qty.     Size      Location            Qty.    Bearing Set
4      5x10mm     Fr Wheels            2      DTXC1535
4      5x10mm     Rear Wheels          2      DTXC1535
2      10x15mm    Fr Diff              1      DTXC1595
2      10x15mm    Rear Diff            1      DTXC1595
2      4x8mm      Servo Saver          1      DTXC1511
2      4x8mm      Middle Lay Shaft     1      DTXC1511

Body pictured on the box is painted red with all decals applied.
It is not possible to request a specific radio channel because they
are supplied by the manufacturer at random.

ACCESSORIES

THIS IS THE RTR HPI SPRINT 2 ON-ROAD TOURING CAR W/TOYOTA TRUENO BODY.
FEATURES: 17 TURN MOTOR, 4 WHEEL BELT DRIVE, OIL FILLED SHOCKS, PLANETARY GEAR
DIFFS, UNPAINTED BODY, ADJUSTABLE TURNBUCKLES THROUGHOUT, 2-CH AM RADIO, ESC
W/REVERSE, D-COMPOUND TIRES, DECALS
REQUIRES: 8 AA BATTERIES, 6-CELL STICK PACK, CHARGER, BUILDING & TRACK EQUIP.

 |  On-Road Nitro  |  Off-Road Nitro   |   On-Road Electric  |  Off-Road Electric  |  Search  |