HPI706    RTR Sprint 2 w/Venom T-10 Painted/200mm

TECH NOTES

This is the 1/10 scale electric powered, radio controlled, Ready To Run
HPI Sprint 2 on-road Touring Car with the Venom T10 Pickup Body.
_
FEATURES: Chassis: Reinforced molded nylon chassis, upper deck and shock towers
Drive: Four wheel
Drive Type: Urethane belt
Motor: Tornado 17 turn
Radio: HPI (made by Airtronics) AM TX-2 pistol grip with steering and
throttle trim, dual rate adjustment, charge jack and servo reverse,
standard size servo
Electronic Speed Control: Hawk Power Reverse
Full ball bearings: Located in transmission and bell crank, rubber
sealed bearings in wheels, 14 total
Shocks: Four oil-filled, plastic bodied
Differentials: Planetary gear type with metal outdrives, sealed
Transmission: Ball bearing equipped and capable of handling modified
motors down to 10 turns
Wheels: 6 spoke chrome 1" (26mm) wide, 2" (51mm) diameter, 6mm offset
at rear, 3mm offset at front
Tires: X-pattern D compound 1" (26mm) wide 2.5" (64mm) outer diameter
Bumpers: Front, foam
Body: Fully trimmed and painted with rear wing and decals applied
Battery: 1800mAh 7.2V 6-cell with standard connector, chassis also
accepts saddle pack batteries
Charger: AC wall, charges battery in six hours
Suspension: Fully adjustable
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Ackerman: Adjustable, Ackerman describes the effect of the inside
front wheel turning tighter than the outside front wheel
Steering: Bell-crank type with servo saver

INCLUDES: HPI Sprint 2 on-road Touring Car with oil-filled shocks, 17 turn
motor, Electronic Speed Control,  painted body, tires, foam inserts
wheels, 28 tooth pinion gear, 87 tooth spur gear, instructions, 2-
channel radio, 1800mAh battery pack, AC wall charger, 2 and 3° rear
toe-in blocks, 4 and 6° front caster blocks, Sprint 2 decal sheet

REQUIRES: AA batteries: 8 for transmitter
Misc. Items: Building and track equipment

SPECS:      VEHICLE-
Length: 17" (431mm)
Width:   7.5" (190mm)
Height:  5" (127mm)
Weight:  3.1lbs (1425g) Ready-To-Run
Wheelbase: 10" (254mm)
Front Tread: 6.5" (166mm)
Rear Tread: 6.9" (175mm) side-to-side at wheel centers
Front Track: 7.3" (186mm)
Rear Track:  7.75" (197mm)
Ground Clearance: 0.41" (10.5mm)
Gear Ratio: 6.62:1
Tires- Front and Rear: 1" x 2.5" (26mm x 64mm)
BODY-
Length: 17.5" (444mm)
Width:   7.9" (200mm) at rear wheels (widest point)
7.7" (197mm) ahead of front wheels (thinnest point)
Height:  4.7" (119mm)

COMMENTS: For Replacement Ball Bearings use:
Qty.  Size      Location                 Qty. Bearing Set
4   5x10mm    Front Wheels               2   DTXC1535
4   5x10mm    Rear Wheels                2   DTXC1535
2   4x8mm     Servo Saver                1   DTXC1511
2   5x8       Fr Diff Shafts             1   DTXC1523
2   5x8       R Diff Shafts              1   DTXC1523
2   10x15mm   Fr Ball Diff               1   DTXC1595
2   10x15mm   R Ball Diff                1   DTXC1595
Body pictured on the box is painted neon green with dark and light
gray flames

ACCESSORIES

THIS IS THE RTR HPI SPRINT 2 ON-ROAD TOURING CAR W/VENOM T10 TRUCK BODY.
FEATURES: 17 TURN MOTOR, 4 WHEEL BELT DRIVE, OIL FILLED SHOCKS, PLANETARY GEAR
DIFFS, TRIMMED AND PAINTED BODY, ADJUSTABLE TURNBUCKLES THROUGHOUT, 2-CH AM
RADIO, ELECTRONIC SPEED CONTROL W/REVERSE, D-COMPOUND TIRES, 1800MAH BATTERY
REQUIRES: 8 AA BATTERIES, BUILDING & TRACK EQUIPMENT

|  On-Road Nitro  |  Off-Road Nitro   |   On-Road Electric  |  Off-Road Electric  |  Search  |