HPI10052   Nitro 3 EVO+ 1966 Mustang GT RTR

TECH NOTES
     This is the 1/10 scale glow powered, radio controlled, Ready To Run
              HPI Nitro RS4 3 Evo+ with the 1966 Mustang GT body.

    **Additional Technical Info Will Be Added When It Becomes Available.**

FEATURES: Chassis: 0.098" (2.5mm) 6061 aluminum, purple in color
          Drive: Four wheel shaft drive
          Engine: Nitro Star G3.0 3.0cc (.18 cu in) 2.2hp with pull-starter,
            can be bump started in racing applications) ABC cylinder and liner
            construction-"A"luminum piston,"B"rass cylinder liner that is
            "C"hrome plated, lightweight aluminum con rod, 2 needle 6.5mm
            rotary carburetor, 2 stage air filter, HPI Roto-Start electric
            starter
          Exhaust: Dual chamber aluminum tuned pipe with tube header, black in
            color
          Radio: Two channel 27MHz AM with steering and throttle trims, dual
            rate for steering and charge jack for optional NiCd battery
          Servos: Two standard size and torque
          Fuel Tank: 2.53oz (75cc), flip top cap
          Clutch: 2-shoe
          Transmission: Two-speed, adjustable
          Ball Bearings: 18 rubber sealed
          Shocks: Four oil-filled, with coil-over spring
          Main Gear: 47 and 43 tooth composite construction main gears
          Clutch bell: 22 teeth and 18 teeth gears that thread onto clutch bell
          Gearbox: Sealed, front and rear
          Differentials: Sealed, with metal bevel gears, limited slip front
            differential
          Brakes: Single disc, fiber construction
          Tires: D compound X-pattern 1.02" (26mm) wide, 2.5" (65mm) diameter
          Wheels: Vintage 5-spoke matte finish chrome
          Body: Pre-painted and trimmed with rear wing and decals applied
          Bumper: Front foam
          Suspension: Four wheel independent
          Caster: Adjustable, caster/toe-in refers to the angle of the front
            suspension when viewed from the side of the car in relation to the
            chassis
          Camber: Adjustable, camber refers to the angle of the tops of the
            tires from vertical when viewed from front or behind vehicle
          Steering: Bellcrank
          Servo Saver: Included

INCLUDES: HPI RS4 3 Evo+ oil-filled shocks, tuned pipe, 3.0cc engine, trimmed
            and painted polycarbonate body, tires, foam inserts, wheels, decals
            AM 27MHz 2-ch radio, Roto-Start and instructions

REQUIRES: AA Batteries: 12 (8 for radio, 4 for battery box)
          6-Cell Flat Battery Pack: For Roto Start
          Battery Charger: For Roto Start battery
          Track Equipment: Fuel bottle, glow starter
          Fuel: 2-stroke glow fuel with 10%-15% nitromethane, 16% lubricant-
            Most of the fuels we carry meet or exceed the lubricant content
            required for optimum performance and maximum engine life. In the
            past, the conventional lubricant content used in fuel was 18%. But
            with new advanced technologies, fuels like Red Alert and O'Donnell
            for example, have a better quality of lubricants even though the
            percentages of lubricant content are lower. These high-tech
            lubricants provide exceptional cooling and protection.

SPECS:      Vehicle-
          Length:
          Width:
          Height:
          Weight:
          Wheelbase:
          Front Tread:
          Rear Tread:
          Front Track:
          Rear Track:
          Ground Clearance:
            Body-
          Length:
          Width:
          Width:
          Height:

COMMENTS: For Replacement Ball Bearings use:
            Qty.  Size       Location                    Bearing Set Qty.
            (2)  10 x 15mm  spur gear shaft             (use 1-DTXC1595)
            (4)   5 x 11mm  front & rear gearbox        (use 2-DTXC1547)
            (4)  10 x 15mm  front & rear gearbox        (use 2-DTXC1595)
            (2)   5 x 11mm  front wheel hubs            (use 1-DTXC1547)
            (2)  10 x 15mm  front wheel hubs            (use 1-DTXC1595)
            (4)   5 x 11mm  rear wheel hubs             (use 2-DTXC1547)
            (2)   5 x 10mm  clutch bell                 (use 1-DTXC1535)

           The Nitro 3 EVO+ with Mustang body is available in the following
             channels;
             A1    HPID52A1
             A2    HPID52A2
             A3    HPID52A3
             A4    HPID52A4
             A5    HPID52A5
             A6    HPID52A6

ACCESSORIES
 THIS IS THE HPI NITRO RS4 3 EVO+ RTR ON-ROAD CAR KIT WITH 1966 MUSTANG BODY.
FEATURES: STEEL DOGBONES, COVERED & REMOVABLE RADIO TRAY, .18 ENGINE W/ROTO
 START, AM PISTOL GRIP RADIO, 2-SP ADJUSTABLE TRANSMISSION, OIL-FILLED SHOCKS
REQUIRES: 12AA BATTERIES, 6-CELL FLAT BATTERY PACK & CHARGER, FUEL, GLOW
 STARTER, TOOLS

 |  On-Road Nitro  |  Off-Road Nitro   |   On-Road Electric  |  Off-Road Electric  |  Search  |