Traxxas Engines, PRO .15 LONG CRANK W/PULL START

Traxxas
Engines

Hobbies R Us

Traxxas
Engines

R/C Airplanes

R/C Boats

R/C Cars

Engines

Engine Parts

Fuel

Click Here For Pricing & Stock Availability

TRA4010   Traxxas   TRX Pro .15 w/Pull Start Standard

TECH NOTES
   This is the Standard Crankshaft Version of the Traxxas Pro TRX-15 Engine.
It is for those who want higher performance than a .12 size engine in their
1/10 scale kit.  This Will Fit Standard Long Crankshaft Applications.

INCLUDES: One Assembled Engine
          One Air Cleaner (Rubber with Foam Element)
          One Full Instruction Book/Warranty Card
          One "Traxxas" Decal Sheet
          Two Replacement Head Gaskets
          One Installed Glow Plug (Standard Long--No Idle Bar)

FEATURES: ABC (Aluminum Brass Chrome) Construction
          Precision Ball Bearings
          Oversized Blue Anodized Cylinder Head
          Black Recoil Assembly (This Makes it a "Pull-Start" Engine)
          Standard-Size Crankshaft
          Fully Adjustable Carb and Needle Settings
          Double O-Ring Seals On Each Needle
          Channelled-Beam Connecting Rod for Improved Oil Flow
          Traxxas Lifetime Engine Replacement Policy

SPECS:    According to Traxxas, this engine will produce 20% more power than
            the TRX-12.  Which is approximately 9-11% more power than the OS
            CZ-Z.  These figures are tested on a dyno (loaded) which provides
            power curves on a computer.  Traxxas was not able to provide any
            numbers on BHP, bore, stroke etc.  Keep in mind that these figures
            are often useless, as they will vary from engine to engine.  And
            there are other variables to consider: the kit, terrain, %nitro
            in fuel, etc....
          Overall Length (from end of shaft to back of recoil): 92mm (3-5/8")
          Length of Crankshaft (from drive washer):             15mm (19/32")
          Length of Crankshaft (from crankcase):                22mm (7/8")
          Height (top of cylinder head to bottom of backplate): 93mm (3-5/8")
          Width:                                                51mm (2")
          Mount Holes (center to center): left to right:        31mm (1-1/4")
                                          front to back:        11mm (7/16")
          Overall Width of Mounting Ears (where the holes are): 40mm (1-9/16")
          ***Mounts the same as an OS .12 and .15 CV***

REQUIRES: 1/10 scale Kit to put it into and 5%-20% Glow Fuel.

COMMENTS: For the Pro 15 with the Short Crankshaft, use TRAG4007.
          For the Pro 15 with the Long Crankshaft, use TRAG4009.
          The kits that this engine fits into are:
            4007 fits: Nitro Rustler, Nitro Stampede, RC10GT, and the Losi GTX
            4009 fits: Nitro Hawk, Nitro Buggy, and Nitro Street
          If you have any other kit, I would call the manufacturer thereof-
            or call Traxxas directly at 1-888-TRAXXAS.
          Traxxas engines run much hotter than "normal" engines (O.S., ASP,
            Thundertigre, etc.).  Therefore, Traxxas recommends their Top Fuel
            (TRAP5010) and their glow plug (TRAG3230) to run the engine cooler.

                                                               
ACCESSORIES
  THIS IS A .15 SIZE, SIDE EXHAUST GLOW ENGINE W/STANDARD LENGTH CRANKSHAFT.
INCLUDES: GLOW PLUG, AIR FILTER, RECOIL STARTER, INSTRUCTIONS AND EXPLODED VIEW
REQUIRES: GLOW FUEL, EXHAUST SYSTEM DEPENDING ON THE VEHICLE AND STARTING
          EQUIPMENT LISTED IN THE VEHICLES FIELD EQUIPMENT LISTING.